Christie CP2000-M Guide d'installation Page 25
- Page / 74
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Section 2: Basic Operation
CP2000-M/MR Setup Guide 2-17
020-100205-03 Rev. 1 (05/09)
Power ON or OFF
Enable ( ) Power On to enter STANDBY mode. Power to projector components is present. Disable
checkbox to turn power OFF.
Turn Lamp ON or OFF
Enable Lamp On ( ) to turn the lamp ON. If an error exists, which will not allow the lamp to turn
ON, the button is grayed out. Disable checkbox to turn the lamp OFF.
Open or Close Douser (Shutter)
Enable Douser Open ( ) to open the douser. Disable checkbox to close the douser.
Display Test Pattern
Enable Test Pattern On ( ) to display the set of test patterns pre-selected from the Advanced: Test
Pattern menu. If more than 1 test pattern is programmed, selecting it again obtains the next test pattern
in the sequence. To return to the program, select a Channel button again.
Move Auxiliary Lens
Toggle the current location of the optional motorized auxiliary lens mount; position it either in front of
the primary lens (enable Auxiliary Lens ( ) checkbox), or move it out (disable Auxiliary Lens
checkbox).
Intelligent Lens System (ILS)
Select ILS to bring up the control screen used to adjust focus, XY offset and zoom of the ILS. This
menu also enables users to manually override the intelligent lens system settings. When the channels
are changed, the ILS automatically moves the lens to adjust the focus, horizontal (X) and vertical (Y)
offset, and zoom based on the pre-defined settings. Allmanual override settings are lost. This feature
should only be used to make quick changes. Proper adjustments should be made in the Channel:Lens
menu when time permits. There are a total of 64 channels available. When ILS is enabled and the
channel has been specified it begins adjusting each motor. The proper lens type must be selected from
the Advanced:Lens menu beforehand. The position of each motor is then saved onto the system in the
specific channel file. This is not a global feature - instead it is controlled on a per channel basis. When
this feature is enabled the ILS for the currently selected channel is turned ON. NOTES: 1) Operator
access rights required to access ILS from the Main menu. 2) Only Advanced users can modify channel
settings.
- CP2000-M/MR 1
- TABLE OF CONTENTS 3
- 1 Introduction 7
- 1.1.2 Key Features 8
- 2 Basic Operation 9
- 2.1.2 AC/POWER PRECAUTIONS 10
- 2.1.3 LAMP PRECAUTIONS 10
- DANGER 10
- 2.2 POWERING UP THE PROJECTOR 11
- Section 2: Basic Operation 12
- 2.3.1 Projector Power States 13
- ENTER to view 14
- MENU at any time to 14
- EXIT once to 14
- 2.5 CHANNEL MENU 16
- 2.6 LAMP MENU 19
- 2.7 LENS CONTROL MENU 20
- 2.8 STATUS MENU 22
- ===== ===== 23
- 2.11 MAIN MENU 24
- CP2000-M/MR Setup Guide 2-17 25
- 2-18 CP2000-M/MR Setup Guide 26
- 2.12 CHANNEL: 3D CONTROL 27
- 2.12.2 Hardware Setup 28
- 2.12.3 3D Instructions 28
- 2.13 ADMIN MENU 29
- 2.13.2 Admin: Screen Menu 31
- FIGURE 2-14 CROPPING 32
- FIGURE 2-15 LETTERBOX 32
- 2.13.3 Admin: MCGD Menu 33
- 2.13.4 Admin: TCGD Menu 35
- 2.13.5 Admin: Lamp Menu 37
- 2.14 WORKING WITH THE LAMP 38
- Using LiteLOC™ 39
- FIGURE 2-20 ENABLE LITELOC 39
- if desired 40
- 2.15 CINEMA OPERATION 41
- 2.16 NON-CINEMA OPERATION 42
- 3 Installation & Setup 43
- 3.1 POSITION THE PROJECTOR 44
- CP2000-M/MR Setup Guide 3-3 45
- FIGURE 3-3 CONNECT DUCTING 46
- (M-MALM) INSTALLATION 47
- 3.6 INSTALL LENS(ES) 48
- 3.7 INSTALL LAMP 49
- 3-8 CP2000-M/MR Setup Guide 50
- 3.9 CONNECTING SOURCES 51
- WARNING 52
- 3.10.1Adjusting Tilt 53
- 3.10.2Adjusting Feet/Leveling 53
- 3.11 BASIC IMAGE ALIGNMENT 54
- 3.12.1 Adjust Offset 55
- CAUTION 55
- CP2000-M/MR Setup Guide 3-15 57
- 3.13.1 DMD Convergence 58
- 3.13.2 Fold Mirror Adjustment 58
- 4 Maintenance 59
- 4.2 FILTER REPLACEMENT 61
- 4.3 LENS REPLACEMENT 62
- 4.3.2 INSTALL LENS 63
- 5 Troubleshooting 65
- 5.3 CINEMA DISPLAYS 66
- 5.4 NON-CINEMA DISPLAYS 67
- Section 5: Troubleshooting 68
- 5.4.12 Display is “Noisy” 69
- 6 Specifications 71
- Section 7: Specifications 72
- 6.3 POWER REQUIREMENTS 73
- 6.4 LAMPS 73
- 6.5 REGULATORY 74
Produits connexes et manuels pour Projecteurs Christie CP2000-M
Projecteurs Christie LW551i Manuel d'utilisateur
(128 pages)
(128 pages)
© 2020, manymanuals.fr. Tous droits réservés | 1.319 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels