Christie CP2000-ZX Guide d'installation Page 49
- Page / 58
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Section 4: Maintenance
CP2000-ZX Setup Guide 4-3
020-100098-04 Rev. 1 (06-2009)
4.2.2 Other Components
In a normal operating environment check, clean and treat the components listed below every 6 months or so to
help ensure proper lamp and projector function.
Lamp Fan
Do not bend the impeller blades or loosen the balancing weights.
A clogged lamp fan impeller or motor can reduce air flow leading to possible overheating and failure of the
lamp. Clean/treat the impeller as follows:
1. Vacuum loose dirt from the lamp fan impeller.
2. If necessary, use a brush with hot water and suitable detergent.
Igniter
Clean the high voltage terminal and insulator to remove accumulated dust or dirt.
Airflow Interlocks
* 600 CFM is required in projection rooms with ambient temperature above
25
°C or elevation (above sea level) greater than 3000 feet.
The CP2000-ZX uses two airflow interlocks; lamp fan vane switch and extractor vane switch.
The lamp fan vane switch is located within the lamp cooling compartment. The extractor vane switch is
located just inside the top duct on the projector lid. Check and if necessary, clean the switches to remove
accumulated dust or dirt that could impede movement. Within the exhaust duct connected at the top of the
projector, adequate airflow must be maintained and routed outside of the building. Inspect regularly and
confirm that 1) there are no obstructions or “kinks” within the ducting, 2) all air intake areas are unobstructed,
and 3) exhaust airflow is at least 450 CFM*
(measured at the end of the duct when not connected to the
projector). Refer to Section 3.2
Maintaining Proper Cooling
Laminar Airflow Device (LAD)
Whenever checking/replacing the air filter on the side of the projector, also visually check the small square
laminar airflow device (LAD) filter just beyond the filter opening. The LAD filter should be nearly white in
color. If it appears a dark gray color (rare) it will require replacement by a qualified technician only. Contact
Christie or your dealer.
- CP2000-ZX 1
- Table of Contents 3
- 1 Introduction 7
- 1.2 Projector Overview 8
- 1.3 How the Projector Works 9
- 1.4 Typographical Notations 10
- 2 Installation & Setup 11
- 2-2 CP2000-ZX Setup Guide 12
- Figure 2-2 Change 13
- Display Angle of CDP 13
- Figure 2-3 Remove CDP 13
- Figure 2-4 CDP Mounting 13
- Ducting 14
- Figure 2-5 Connect Exhaust 14
- STEP 6 - Install Lens(es) 15
- STEP 7 - Install First Lamp 15
- and Anode Yoke Position 15
- STEP 8 - Connect to Power 16
- CP2000-ZX Setup Guide 2-7 17
- Actual Length 1.5 Meters 18
- CP2000-ZX Setup Guide 2-9 19
- 2.2 Connecting Sources 20
- ). Caution! The RS232 B 21
- 2-12 CP2000-ZX Setup Guide 22
- 2.4.1 Adjusting Tilt 23
- 2.5 Maximizing Light Output 24
- 2.6 Basic Image Alignment 25
- Figure 2-22 Lens Mount 26
- 2.7.1 Adjust Offset 27
- FIGURE 2-26 28
- FIGURE 2-27 28
- FIGURE 2-28 28
- 2.7.3 Add Anamorphic Lens 29
- 2.7.4 Wide Converter Lens 29
- 2.8.1 DMD Convergence 29
- 2.9 Calibrating the System 30
- CP2000-ZX Setup Guide 2-21 31
- 3 Basic Operation 33
- 3.1.3 AC / Power Precautions 34
- 3.1.4 Lamp Precautions 34
- Wear Protective Clothing 34
- Cool the Lamp Completely 34
- 3.2.1 Ventilation 35
- 3.2.2 Air Filter 35
- 3.2.3 Liquid Cooler 35
- 3.3 Powering Up the Projector 36
- 3.4.1 CDP Key Descriptions 37
- 3-6 CP2000-ZX Setup Guide 38
- 3.5.1 User Access and Rights 39
- Section 3: Basic Operation 40
- 3.5.2 Alarm Windows 41
- 3.6 Working with 3D 43
- 3.6.2 Hardware Setup 44
- 3.6.3 3D Instructions 44
- Hardware Instructions 44
- Figure 3-4 Setup for 3D 45
- 4 Maintenance 47
- 4.2 Cleaning the Lens 48
- 4.2.2 Other Components 49
- Lamp Fan 49
- Igniter 49
- Airflow Interlocks 49
- Laminar Airflow Device (LAD) 49
- 4.3 Replacing the Lamp 50
- Section 4: Maintenance 51
- Figure 4-2 Install New Lamp 51
- 4.4 Replacing the Filter 52
- 4.5 Replacing a Lens 52
- 5 Troubleshooting 53
- Section 5: Troubleshooting 54
- 5.3 CDP 55
- 5.4 Ethernet 55
- 5.5 Cinema Displays 56
- 5.6 Non-Cinema Displays 57
Produits connexes et manuels pour Projecteurs Christie CP2000-ZX
Projecteurs Christie CP2000-M Spécifications
(122 pages)
(122 pages)
(8 pages)© 2020, manymanuals.fr. Tous droits réservés | 1.855 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels